Technical reference · 12 September 2026
| Specification | Configuration |
|---|---|
| Radio / platform | Wi-Fi 6E | 4x4 | selectable 2.4 / 5 / 6 GHz |
| Theoretical PHY reference | 4804 Mb/s high-band profile |
| Host / processor | QCN9024; PCIe 3.0 / M.2 E-Key |
| Channel / network configuration | 40 MHz at 2.4 GHz; up to 160 MHz at 5 / 6 GHz |
| RF / power | 4 x U.FL; supply must match exact carrier/revision |
| Mechanical / environment | 57 x 63 x 6 mm; -20 to +70 C |
| Parameter | Pulse P6-06 |
|---|---|
| RF tuning ranges | 2412-2472 MHz; 5150-5950 MHz; 5925-7125 MHz |
| Configuration storage | 2 Mbit serial I2C EEPROM |
| RF allocation | Four transmit / four receive paths on the selected band; four U.FL connectors |
| Power integration | Use the supply and pin assignment approved for the delivered module/carrier revision |
| Environmental design | -20 to +70 C operating; -40 to +90 C storage; 5-95% RH non-condensing |
Model-specific datasheet reference points for RF design. TX is conducted power per RF chain; RX is input sensitivity. Configure channel, output power and antenna gain for the operating country.
| MCS | TX / chain (dBm) | RX sensitivity (dBm) |
|---|---|---|
| MCS0 | 18.0 | -86.0 |
| MCS9 | 13.0 | -65.0 |
| MCS10 | 12.0 | -62.0 |
| MCS11 | 11.0 | -59.0 |
Reference tolerance: ±2 dB.
| MCS | TX / chain (dBm) | RX sensitivity (dBm) |
|---|---|---|
| MCS0 | 19.0 | -92.0 |
| MCS8 | 17.0 | -75.0 |
| MCS9 | 16.0 | -72.0 |
| MCS10 | 15.0 | -69.0 |
| MCS11 | 14.0 | -66.0 |
Reference tolerance: ±2 dB.
Pulse P6-06 uses the ath11k driver family for Linux integration. Prepare the PCIe host, driver, device firmware and calibration as one matched software set. For an OpenWrt host, choose packages built for that host release and kernel ABI, then verify the detected device and radio profiles.
| Integration item | Configuration |
|---|---|
| Radio platform | QCN9024; PCIe 3.0 / M.2 E-Key |
| Driver family | ath11k |
| Firmware lookup family | /lib/firmware/ath11k/QCN9074/hw1.0/ — confirm the path requested in the device boot log |
| Board data | Retain the unit calibration and revision-specific board data; match the PCI/subsystem and board identity. |
| Radio profile | Wi-Fi 6E | 4x4 | selectable 2.4 / 5 / 6 GHz; 40 MHz at 2.4 GHz; up to 160 MHz at 5 / 6 GHz |
| Read-only first checks | lspci -nnk; dmesg; iw phy; iw dev; iw reg get |
Use the following commissioning procedure for Pulse P6-06. This is a test method, separate from the theoretical PHY specifications and datasheet RF references above.
| Step | Record and verify |
|---|---|
| Baseline | Model/revision, firmware build, host CPU, uplink speed, channel width, country profile, antennas and client spatial streams. |
| Link verification | Capture negotiated PHY, RSSI per chain and noise/retry statistics before sustained traffic. |
| Wired reference | Measure the wired path first; select a server link appropriate to 4804 Mb/s high-band profile. |
| Traffic test | Run TCP in each direction, then concurrent clients; record duration, CPU load, temperatures and retransmissions. |
| Site acceptance | Repeat at the intended mounting positions; save results with the exact configuration for comparison. |
524WiFi™ engineering support · Tomorrow Systems®